Log Service allows you to create a custom ID-based machine group. This topic describes how to create a custom ID-based machine group in the Log Service console.
- A project and a Logstore are created. For more information, see Create a project and a Logstore.
- At least one server is available.
- If you use an ECS instance, you must ensure that the ECS instance and Log Service project share the same Alibaba Cloud account and belong to the same region.
- If the ECS instance is purchased by another Alibaba Cloud account, you must configure a user identifier before you create an IP address-based machine group. If the server is provided by another cloud service vendor or is deployed in a user-created data center, you must also perform the preceding operation. For more information, see Configure an account ID for a server.
- Logtail is installed on the server. For more information, see Install Logtail on ECS instances.
- If your servers reside in multiple custom network environments such as virtual private clouds (VPCs), some IP addresses of the servers may conflict. In this case, Logtail cannot collect logs as expected. You can use a custom ID to prevent this issue.
- If you want to add multiple servers to a machine group, you can set the same custom ID for new servers as the machine group. Log Service identifies the custom ID and adds the servers with the same custom ID to the machine group.
- Create a file named user_defined_id in a specified directory.
- Linux: Store the file in the /etc/ilogtail/user_defined_id directory.
- Windows: Store the file in the C:\LogtailData\user_defined_ided_id directory.
- Set a custom ID for the server. Note
- Windows and Linux servers cannot be added to the same machine group. You cannot set the same custom ID for Linux and Windows servers.
- You can set one or more custom IDs for a single server and separate custom IDs with line feeds.
- In the Linux server, if the /etc/ilogtail/ directory or the /etc/ilogtail/user_defined_id file does not exist, you can create the directory and file. In the Windows server, if the C:\LogtailData directory or the C:\LogtailData\user_defined_id file does not exist, you can also create the directory and file.
Set the custom ID in the /etc/ilogtail/user_defined_id file. For example, if you want to set the custom ID to
userdefined, run the following command to edit the file. In the file, enter
Set the custom ID in the C:\LogtailData\user_defined_id file. For example, if you want to set the custom ID to
userdefined_windowsin the C:\LogtailData\user_defined_id file.
- Log on to the Log Service console.
- In the Projects section, click the destination project.
- In the left-side navigation pane, click Machine Groups.
- On the right of the Machine Groups, choose .
- In the Create Machine Group dialog box, set the required parameters, and then click OK. The following table describes the parameters.
Parameter Description Name The name of the machine group. The name must be 2 to 128 characters in length, and can contain only lowercase letters, digits, hyphens (-), and underscores (_). The name must start and end with a lowercase letter or digit.Notice After the machine group is created, you cannot modify its name. Proceed with caution. Identifier The identifier of the server. Select Custom ID. Topic The topic of the machine group. This topic is used to differentiate log data that is generated in different servers. For more information, see Configure a log topic. Custom Identifier Enter the custom ID that is set in 2.
- View the status of the machine group.
- In the list of machine groups, click the destination machine group.
- On the Machine Group Settings page, view the status of the machine group. You can view the list of servers that
share the same custom ID. You can also view the heartbeat statuses of these servers.
- The Machine Group Status section lists the IP addresses of the servers whose custom
ID is the same as the custom ID that you set for the machine group.
For example, the custom ID of a machine group is userdefined and the IP addresses in the Machine Group Status section are 10.10.10.10, 10.10.10.11, and 10.10.10.12. This indicates that you have specified the same custom ID for the servers in this machine group. If you want to add another server to the machine group and the IP address of the server is 10.10.10.13, set the custom ID to userdefined for the server. Then, you can view the IP address of the added server in the Machine Group Status section.
- If the Heartbeat status is OK, the server is connected to Log Service. If the status is FAIL, see What can I do if the Logtail client has no heartbeat?
- The Machine Group Status section lists the IP addresses of the servers whose custom ID is the same as the custom ID that you set for the machine group.
Disable a custom ID
If you want to set the Identifier parameter to IP Addresses, delete the user_defined_id file. The new configurations take effect within 1 minute.
- In Linux, run the following command:
rm -f /etc/ilogtail/user_defined_id
- In Windows, run the following command:
Time to take effect
/etc/init.d/ilogtaild stop /etc/init.d/ilogtaild start
- Choose .
- In the Services window, select the required service.
- For Logtail V0.x.x.x, select LogtailWorker.
- For Logtail V126.96.36.199 or later, select LogtailDaemon.
- Right-click the service and then select Restart to validate the configurations.